1D-Link DGE-528TGigabit Ethernet PCI AdapterManualRev. 01 (Nov. 01, 2003)Printed in Taiwan
10Networking Basics Please wait while the NetworkSetup Wizard applies thechanges.When the changes arecomplete, click NextPlease wait while theNetwork
11Networking BasicsFormat the disk if you wish.Click NextIn this window, selectthe best option. In thisexample, Create a NetworkSetup Disk has beense
12Networking BasicsPlease wait while the Network Setup Wizard copies the files.Please read the information under Here’s how in the screen below. Afte
13Networking BasicsPlease read the information on this screen, then click Finish to complete the Network SetupWizard.The new settings will take effect
14 Click Start (in the lower left corner of the screen) Right-click on My Computer Select Properties and click Selec
15Networking BasicsNaming your Computer In this window, enter the computer name. Select Workgroup and enter the name of the Workgroup.Checki
16Type ipconfig /all at the prompt. Hit Enter. All the configuration settings are displayed as shownbelow.Checking the IP Address in Windows XP/2000
17Note: Residential Gateways/Broadband Routers will automatically assign IP Addresses to thecomputers on the network, using DHCP (Dynamic Host Config
18For help with other tasks in home or small office networking, see Using the Shared Documentsfolder and Sharing files and folders in the Help and Sup
19TroubleshootingA network can be simple to install and maintain. However, occasionally something might go wrong.The best approach to troubleshooting
2Table of ContentsIntroduction ... 3Contents of Package ...
20If you do not see any items branching out after double-clicking “Network adapters,” your NetworkAdapter has not been properly installed. Start at th
21Go to Start> Run.Type in the following: ping xxx.xxx.xxx.xxx, where xxx.xxx.xxx.xxx is the IP address to bepinged (i.e. 192.168.0.1). In this cas
22If the connection is good, you will receive four “Reply from” messages. Type exit at the promptto return to Windows.
Technical SupportYou can find software updates and user documentation on the D-Link website.D-Link provides free technical support for customers with
Technical SpecificationsNetwork Type: Gigabit Ethernet 1000Base-TIEEE 802.3ab standard for 1000 Mbps baseband CSMA/CD local area network Fast Eth
25Host Interface: PCI 2.1 and PCI 2.2 Bus (Bus Master)I/O & IRQ base address: assigned by Plug and Play systemPhysical Dimensions: 14 cm x 5.9 cmE
26D-Link Offices AUSTRALIA D-LINK AUSTRALIA Unit 16, 390 Eastern Valley Way, Roseville, NSW 2069, Australia TEL: 61-2-9417-7100 FAX: 61-2-94
27LIMITED WARRANTY (excluding USA)D-Link provides this limited warranty for its product only to the person or entity who originally purchased the pr
28D-Link of the defective Hardware. All Hardware (or part thereof) that is replaced by D-Link, or for which the purchase price is refunded, shall b
29RETURN THE REGISTRATION CARD MAY AFFECT THE WARRANTY FOR THIS PRODUCT. Submitting A Claim. Any claim under this limited warranty must be submitte
3IntroductionThe D-Link DGE-528T is ideal for the small office or home office environment. After completing thesteps in this manual, you will have the
30Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act of Go
31REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. GOVERNING LAW:
32FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
33CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be req
34Registration Card (excluding USA) Print, type or use block letters. Your name: Mr./Ms ___________________________________________________________
4Contents of Package DGE-528T Gigabit Ethernet PCI Adapter Package Contents 1 DGE-528T Gigabit Ethernet PCI Adapter2 Manual on the CD-ROM3 Quick Inst
5Category 5 cabling is required for 1000Base-T Gigabit Ethernet in order to provide full duplex operation. Full duplex 1000Base-T operation allows si
6The working relationship between a DGE-528T adapter and main memory working in Bus Mastermode is powered by the Bridge/Memory Controller of the PCI b
71. Power-ON the PC and press “Delete” or “F1” when prompted to enter the PCI/ISA BIOS CMOSSetup. Enable the WOL function or the power-ON function of
8Networking BasicsPlease follow all the instruc-tions in this window:In the following window, selectthe best description of yourcomputer.Click Next Cl
9Networking Basics Click NextClick NextEnter a Computer description anda Computer name (optional.)Enter a Workgroup name.All computers on your network
Commenti su questo manuale